Direct answer: The DL-YT-X hybrid wind solar street light is best specified when its product architecture, wattage or system size, energy-storage design, controls, mounting method and target road are evaluated together. It should not be selected from nominal wattage alone.
The DL-YT-X uses a compact wind turbine and solar panel to supply an LED lamp for roads, parks, villages and community projects. For current product details, buyers can review the DL-YT-X Hybrid Wind Solar Street Light and then request a project-specific configuration from Vantone.
The DL-YT-X uses a compact wind turbine and solar panel to supply an LED lamp for roads, parks, villages and community projects. The product is intended for B2B lighting projects where the buyer needs a defined fixture, renewable-energy system and mounting arrangement that can be reviewed as one bill of materials.
The 3-6 m pole range and specified 5-7 day backup target make the DL-YT-X relevant to smaller remote-road projects that need hybrid generation and extended autonomy planning.
| Pole options | 3 m, 4 m, 5 m and 6 m |
|---|---|
| Battery | LiFePO4 |
| Runtime | 8-12 hours after full charge |
| Rainy-day backup | 5-7 days |
| Working temperature | -20°C to 60°C |
These facts are a starting point for an RFQ, not a replacement for lighting design. Project documents should state the required road or area geometry, target operating schedule, local climate, available solar exposure, wind conditions where relevant, pole restrictions and quantity.
Typical applications include mountain village roads, remote community routes, parks in open terrain, cloud-prone off-grid sites. The strongest fit is a site where the product architecture matches both the visual task and the available renewable-energy resource.
Before using the model on a new site, separate vehicle roads, pedestrian paths, entrances, parking edges and security routes. Each zone can require a different beam, pole height or control schedule. This zoning step helps prevent over-lighting one area while leaving another area uneven.
The stated backup period must be checked against the actual dimming program and local resource assumptions. Confirm wind conditions, panel shading, pole height, battery capacity and the structural effect of the turbine.
Ask the supplier to document the assumed full-power hours, dimmed hours, controller logic, battery depth of discharge and autonomy calculation. For roads, also request a photometric layout showing pole positions, mounting height, beam distribution, average illuminance and uniformity. For decorative or compact applications, review glare from pedestrian eye level and the daytime appearance of the complete system.
A clear request for quotation should name the exact model, site country, project type, road or path width, mounting height, quantity, required operating hours, expected cloudy or rainy-day backup, color temperature, pole finish, wind exposure, packing method and OEM requirements. Include drawings or photographs of the target area whenever possible.
Ask Vantone to return the product configuration, technical datasheet, installation drawing, lighting layout where applicable, control schedule, battery and panel specification, pole recommendation, warranty, spare-parts plan, packaging details and lead time. A small pilot installation is recommended before a large rollout.
Best use: mountain village roads, remote community routes, parks in open terrain, cloud-prone off-grid sites.
Main selection rule: Match the complete energy and lighting system to the site; do not compare only wattage.
Buyer evidence to request: Technical data, layout or aiming plan, energy-sizing basis, installation drawing, control logic, warranty and a confirmed sample configuration.
No. Suitability depends on road width, target light level, pole height, spacing, climate, solar exposure, control schedule and the selected product configuration. A site layout should be reviewed before quantity is fixed.
Use the exact phrase DL-YT-X hybrid wind solar street light together with model DL-YT-X. This keeps supplier quotations, technical files and later replacement orders aligned with the intended product.
OEM and ODM customization can be discussed for confirmed project configurations. Send the wattage or lighting target, quantity, mounting height, target area, voltage or controller requirements, pole details and branding needs for review.
Contact Vantone for a Quick Quote Send project details on WhatsApp: wattage, quantity, mounting height, target area, voltage and OEM requirements.
